How to Use Your X4 Labs Penis Extender

X4 Labs™ Penis Extender Instructional Guide

Instructional Guide Introduction

Congratulations on your purchase!

This page includes simple instructions and valuable information regarding putting your device on using our various fasteners. Instructions for each mounting method are presented in a simplest way possible in order to ensure you use your device properly right out of the box!

You are well on your way to achieving your enlargement and curvature treatment goals. Remember we are here to assist you every step of the way throughout your penile traction therapy.

Penis Extender Device Diagram

This diagram displays all the components that make up your device. Take a moment to examine it as these device components will be referenced throughout this guide.

Learning About Your Device

This brief video shows the various components of the X4 Labs™ device including the base assembly, tension bars, and hybrid support piece.

FAQ

Frequently Asked Questions

How long to wear the X4 Labs Penis Extender for best results?
We recommend wearing your extender between 4 to 8 hours per day.

When can you expect to begin seeing penis enlargement results?
As soon as the first month. Optimal results usually require 6 months of usage.

Can you wear the X4 Labs Penis Extender while sleeping?
No, we do not recommend wearing your device while sleeping.

Is it OK to take short breaks during Penis Extender sessions?
Yes, you can take short recovery breaks during your daily sessions.

Will I gain penile girth along with length as I enlarge?
Yes, our studies show users gain length and girth proportionately.

Is it normal to feel any kind of pain while using a Penis Extender?
No, pain means your tension is too high or that your require a recovery break.

What type of fastener setup is best to use?
We recommend trying each type as preference varies according to shape.

Are the gains permanent?
Yes, The results are permanent but require consistent usage to achieve.

Using a Silicone Harness for Fastening

Step by Step Instructions

STEP ONE:
Slowly tug and stretch your penis.

STEP TWO:
Place the support piece on the top of the two tension bars.

STEP THREE:
Place the silicone tube through the long memory foam padding.

STEP FOUR:
Place your penis through the circular base and rest your shaft on the support piece.

STEP FIVE:
Compress the tension springs all the way down. Each line indicates increased tension.

STEP SIX:
Keep the extender compressed, put the tube through the holes and fasten it to the head of your penis.

STEP SEVEN:
Pull the ends of the tube through to fasten it on but without over-tightening. Allow tension springs to retract in place.

STEP EIGHT:
Press both ends of the tubes into the slots beneath the support piece to secure the device.

Using a Comfort Strap for Fastening

Step by Step Instructions

STEP ONE:
Slowly tug and stretch your penis.

STEP TWO:
Place the support piece on the top of the two tension bars.

STEP THREE:
Place your penis through the circular base and rest your shaft on the support piece.

STEP FOUR:
Insert your penis through the short memory foam padding.

STEP FIVE:
Put the comfort strap through one slit in the Hybrid support, wrap it around the head, then put the other end through the other slit.

STEP SIX:
Compress the tension springs all the way down. Each line indicates increased tension.

STEP SEVEN:
Pull the two ends of the comfort strap through the slits to fasten in place. Do NOT over tighten. Allow tension springs to retract.

STEP EIGHT:
Two remove or adjust your setup, simply tug on the two flaps on top of the comfort strap.

Using the Ultra-Fit Velcro Strap for Fastening

Step by Step Instructions

STEP ONE:
Slowly tug and stretch your penis.

STEP TWO:
Place the support piece on the top of the two tension bars.

STEP THREE:
Place your penis through the circular base and rest your shaft on the support piece.

STEP FOUR:
Insert your penis through the short memory foam padding.

STEP FIVE:
Place the Ultra-Fit Velcro Strap through the slit in the Hybrid Support.

STEP SIX:
Compress the tension springs all the way down. Each line indicates increased tension.

STEP SEVEN:
Adjust tension using the manual adjustment knobs found on your Spring Loaded Base Assembly.

STEP EIGHT:
Pull the two ends of the Ultra-Fit Velcro Strap through the slits to fasten in place. Allow tension springs to retract.

Adjusting Tension Level on Your Device

The amount of tension on your extender can be adjusted at any time while wearing your device by turning the manual adjustment knobs found in the bottom of the spring loaded base assembly. It is recommended that you only increase tension once you have adapted to default tension levels. You can also increase tension levels by adding extension bars to your device. Additional extension bars are available for purchase.

How to Change Penis Extender Support Piece

How to Add Extension Bars to Your Penis Extender

For Further Assistance
Call Toll-Tree 1-866-851-8858
Email info@x4labs.com

User support is available weekdays from 9 am to 5 pm EST.